ICE


I've seen a few posts on Pistonheads.com asking about how people have fitted their component speakers, so I thought I'd show how I did mine!

I fitted a set of 5.25" Focal V Slims to the front, the main units fit perfectly in the standard holes, I did have to drill new holes for the screws but apart from that straight forward. The crossover got secured to the inside of the door panel. The 1" tweeters were fitted to the top of the door card facing the front seats.

The rear speakers used to be a set of JBL 6 x 9" units when I bought it, these were fitted to a piece of MDF covered in the same carpet as the interia. Given that it used to take up all the room behind seats I decided to get rid of it. A couple of screws later and it was out. In there place I got a couple of Infinity 5001i units, these are fitted in the air vents on the rear bulkhead, I used a couple of 1" square blocks of wood on each speakers as spacers, so that the vents still did there job and the speakers pointed in the right direction.

The bass is sorted by fitting a slim line Alpine SWD-1600 subwoofer behind the passenger seat, always makes the ladies smile...dunno why ;)

I swapped out the head unit for another Pioneer model (DEH-P5600MP), the main reason is that I could still use the existing CD changer in the boot. I also bought an extra unit so I could use the AUX input on the HU, this means I can plug in my mp3 players or TomTom.


OK a lot of people say that I should be listening to the cars V8 soundtrack, but if I'm just pottering around town I like to have something to sing along to :)

Comments

Anonymous said…
This site was... how do I say it? Relevant!! Finally I've found something which helped me.
Thanks a lot!

my weblog :: Marlene
4:39 am
Post a Comment

Popular posts from this blog

Dashboard Replacement

Image
During this summer the veneer on the dashboard started to crack a bit more, so I decided to replace it with a Leven alloy item. After reading up on www.chimaerapages.com and using Steve Heaths bible I set off removing the old dash and putting the new shiny one in...Here's a bolt by bolt guide on how I completed it- Dash top removal: Unscrew the passenger "glove box" under the dash Find and remove the three elusive bolts that hold the dash top on Now try and move the dash top into a position where you can get the right hand side bolt to come free, this was completed with a lot of swearing and sweating Dashboard removal: Work your way along the dials and switches removing them from the old dash one-by-one and reconnecting them separated from the dash Unscrew the screws that hold the heater controls to the dash bottom, keep hold of the bolts that are used as spacers between the controls and the dash bottom Now you should be able to lift the old dashboard from the dash bottom...
Read more

Roll Bar and Harness

Image
Roll Bar Fitting I took delivery of a TR Lane Fabrications roll bar a while back now and finally got around to fitting it this spring. Fitting was eventful as with anything that's made to fit handmade motors and is not fabricated on site... The first step was to find the seat belt anchor points on the chassis, with the roll bar came a treasure map to locate these, so it was just a matter of drilling a few holes and removing the glass fibre around the anchor points. This is a bit of a pain due to the lack of space behind the seats but with a bit of patience and test fitting big enough holes where created. The bottom of the roll bar is secured behind the seats by the bolts that holds the body to the outriggers, so it's a matter of carefully pulling up the carpet and removing these. Bolting the roll bar in place was aided by the use of a ratchet strap as it just wasn't the correct size to fit the car. I firstly loosely bolted the bottom of the roll bar in place... Then usin...
Read more

Mod-Wise Boot Opening and Light Kit

Image
Well another day and another Mod-Wise kit to fit, after this I should have the ability to open the boot from the outside, without having to put the keys in the ignition and press the button under the dashboard, and I should be able to see in the boot at night!! Here's how I went about it: Fitting the relay to the boot actuator. This was a matter of pulling up the carpet in the boot to the right hand side of the boot catch (as you look at the car from the rear) and finding the wires that feed the boot latch actuator, here are mine (picture taken from inside the boot looking backwards, the light pod is the off-side rear): Now attach the wires with the supplied clips, and I've also taped the relays in place with good old duck tape! Now it's a matter of feeding the door micro-switch and it's wire around the boot, again I used little strips of duck tape to keep it in place, and fed the switch over the near side wheel arch and through to the passenger door lock actuator. This...
Read more